Back to all devices

Tuya TS0601_smoke_co in Home Assistant

Smoke & safety · Zigbee · Dual smoke CO sensor

Zigbee2MQTT Quirk proposed, not merged yet 2 open reports

Zigbee device – see the note above on what ZHA needs for it.

Brand: Tuya
Model: TS0601_smoke_co
Device type: Smoke & safety
Radio: Zigbee
Power: Battery
Reports itself as: _TZE284_6ycgarab, _TZE284_aoah6bv8, _TZE2841000000_6ycgarab
Also sold as: Moes JKD-513COM-Z
Zigbee2MQTT: Device page on zigbee2mqtt.io

How the device gets into Home Assistant

official ZHA – with a Zigbee coordinator and the ZHA integration; for all its functions it needs a custom quirk, see above. Integration
official Tuya Zigbee gateway – paired with a Tuya Zigbee gateway and controlled through the Tuya cloud with the Tuya integration. Integration
add-on Zigbee2MQTT – Zigbee2MQTT runs as an add-on and passes the device on to Home Assistant over MQTT. Integration · Source

Known problems and fixes

Requests for ZHA support

support requested The Tuya Smoke/CO Detector TS0601 is not supported in ZHA, so it cannot be used with Home Assistant without additional configuration. since January 9, 2026 · zha-device-handlers #4638
support requested A request to add support for a TS0601 smoke/CO detector, which is not currently recognized by Home Assistant. since July 11, 2025 · zha-device-handlers #4181

Changes proposed for ZHA

pull request The MOES JKD-513COM-Z smoke and CO detector is not recognized by ZHA. Adding its quirk would allow Home Assistant to trigger alerts for smoke and carbon monoxide detection. since September 12, 2026 · zha-device-handlers #5326

ZHA quirks for this device

Quirk proposed, not merged yet Recommended quirk

Proposed to ZHA and waiting for review – the maintainers check it before it becomes part of Home Assistant.

Adds: Fault bitmap Silence alarm

Source: zha-device-handlers · pull request #5326 · by @kaka8812345678-stack · September 12, 2026
Signature: _TZE284_aoah6bv8 / TS0601

1 more quirk for this device

Custom quirk shared in an issue _TZE284_6ycgarab / TS0601 zha-device-handlers · issue #4181 · by @foooji · October 7, 2025

The quirk is not part of ZHA yet. You can use it as a custom quirk until it is:

Tell ZHA where custom quirks are kept – in configuration.yaml:
```
zha:
  custom_quirks_path: /config/custom_zha_quirks/
```
Create that folder and save the quirk as a .py file in it.
Restart Home Assistant. If the device was paired before, reconfigure it or remove and pair it again so the quirk is applied.
Check it worked: the device page shows the quirk under Zigbee info.

A custom quirk has not been reviewed by the ZHA maintainers. Delete the file once the quirk is part of a Home Assistant release – otherwise the old copy takes precedence.

All quirks in the ZHA quirk database →

Alternatives

The same job from other makers – devices of the same type and radio that work with Home Assistant too.

Moes ZSS-HM-SSD01 Smoke & safety · Zigbee · Smoke sensor Zigbee2MQTT ZHA quirk 1 open report Review · from 32.99 €
Develco SMSZB-120 Smoke & safety · Zigbee · Smoke detector with siren Zigbee2MQTT ZHA quirk 2 open reports Review
Alecto SMART-SMOKE10 Smoke & safety · Zigbee · Smoke detector Zigbee2MQTT Review
Aqara JT-BZ-01AQ/A Smoke & safety · Zigbee · Smart natural gas detector Zigbee2MQTT Review

Sources: Zigbee2MQTT, ZHA quirks, Z-Wave JS, the Matter certification database, Shelly, ESPHome, Tasmota, Tuya Local and the issue trackers on GitHub. Reports are assigned to a device by the identifiers they contain; the sentences come from the integration pages, where a language model writes them from the titles.